Real parts built from text
Hollow box with M3 pilot holes
200 mm wide 40 mm deep 40 mm high deep hollow box with closed top and rounded corners. 5 mm corner radius. hollow on bottom. 5 mm wall. m3 pilot holes on all 4 corners. 5 mm recessed lip on bottom.
Mechanical arm link
Elongated rectangular link, 173mm long, 38.1mm wide, 10.2mm thick, with rounded ends, two 12.7mm holes 152.4mm apart, and 2mm fillets on external edges.
Enclosure base with standoffs
96x68x26mm open-top enclosure with 2.4mm walls, 12.5mm holes in left and right walls, and four 6.5mm standoffs with 2.5mm screw holes on the bottom
Base plate with slots
Flat plate 130x90x3mm with R5mm corners, 4x Ø3.2mm holes, 2x 3x15mm slots, 1x 10x5mm cable-pass slot with R2.5mm ends
Upper arm plate
Flat 2D plate, 50x22x3mm, R11 rounded ends, with two 3.4mm holes at (11,11)mm and (40,11)mm
Gripper mount plate
Flat plate, 26x22mm, 3mm thick, with holes: 1x Ø3.4mm, 2x Ø2.0mm, 3x Ø3.2mm
Business card chute
A 3D printable low-profile rectangular vertical chute for standard business cards. The overall outer dimensions are exactly 50.8mm width, 88.9mm depth, and 20.32mm height. The exterior walls are 3mm thick. The top face is completely open, creating a single unified short vertical channel for cards to rest flat inside. The inside bottom floor is solid and flat.
Plate with 150 mm bore
Rectangular plate, 175x465x30mm, with a 150mm hole centered at 165mm from one edge, and R2 rounded edges.
Telescope collimation cap
Hollow cylinder, OD 31.7mm, height 35mm, with a 38mm OD top flange, 5mm high, and a 1.5mm central pinhole on the top face.
Pencil case
Rectangular prism pencil case, 200mm long, 100mm wide, with a flat top and bottom
Electronics box with 8 compartments
Enclosure box with 8 compartments, base gap for electronics, and a long top border for a lid, wall thickness 2mm
Plate with M3 centre thread
We need the plate 60 mm length and 30 width and 3 mm thickness and make the m3 thread in center of the plate
Retention clip with pins
Rectangular clip with 15.8x5.0x5.0mm central block, two 2.3mm diameter, 6.35mm long pins, spaced 7.9mm apart, and a chamfered top edge
Desktop organizer tray
Rectangular tray, 240x150x40mm, 3mm walls, with three vertical dividers and six 12mm ID, 35mm deep cylindrical tubes on the right side.
Three stacked cylinders
Three stacked cylinders, each 300mm tall, with diameters 800mm, 550mm, and 300mm, from largest to smallest.
Duct pipe reducer
2mm thick duct pipe reducer, 65mm opening from one side, 50mm long reduced to 125mm other side. from both sides a neck 30mm
20-tooth spur gear
Create one solid spur gear with exactly 20 teeth, outside diameter 50 mm, thickness 10 mm, a 5 mm through bore, and a flat bottom. Use an involute profile with 20 degree pressure angle. The outside diameter is the tooth-tip diameter, not the pitch diameter. Keep it a single watertight printable solid.
Block with rectangular pocket
Cube 100x25x30mm with a 91x16x5mm rectangular depression in the 100x25 face
Open-top enclosure with board posts
Open-top enclosure box, internal 155x126x18mm, with 4 internal mounting screw posts at corners for 150x121mm board, cable clearance slot on right side, and flat mounting tabs with screw holes on outer edges
Electronics enclosure with corner bosses
Rectangular enclosure base, 153x103x35mm internal, 2mm walls. Add 8mm solid mounting bosses in the four inside corners. Attached to the top outer edge, add a secondary 153x25mm compartment with a slatted grill top. Create a 10x5mm cutout on the right side wall.
Watch bezel ring
Watch case bezel, 41mm outer diameter, 2mm thick, with a circular opening.
Watch dial plate
Flat circular plate, 32mm diameter, 0.8mm thick
USB stick enclosure with lid
Compact rectangular USB enclosure, 60x20x8mm, with a 57x17x1.5mm internal cavity, a 14.5x4mm USB connector opening, and a separate top cover.
AMR chassis plate
Rectangular chassis, 300x220x8mm, with rounded corners and lightweight cutouts, flat top surface
Coffee cup coaster
Make a coffee cup coaster
Countertop NFC display stand
Countertop NFC display stand with 100x140x5mm card, 12-degree tilt, 110x65x7mm base, and 25.5mm NFC pocket
Rotating platform disc
Flat circular disc, Ø40mm, 3mm thick, with 4 Ø2mm holes on Ø12mm bolt circle at 0°, 90°, 180°, 270° and 2 Ø3.2mm holes at (-15,10) and (15,10)mm
Letter S keychain hook
The Letter "S" with a small hook to be added to a keychain. the overall size should be about 40 mm
Load cell box with lid
Hollow box, 80mm inner width, with a pocket for an 80mm bar load cell, and a separate top lid, 2mm smaller than the box inner perimeter, with a central bottom pillar
M8 x 50 hex head bolt
Hex head bolt M8 x 50mm, metric coarse thread pitch 1.25mm, head across flats 13mm, head height 5.3mm, DIN 931
Self-watering planter body
Open-top planter body, 150mm diameter, 130mm tall, with a 100mm diameter, 50mm tall removable water reservoir and a 120mm diameter, 20mm tall elevated grow basket